Your TV is not only a big source of entertainment in your life but also acts as essential equipment for home décor. A sleek looking flat-screen smart TV mounted on an attractive wall is just what you need to add more elegance to your home.
Thus, if you wish for a perfect fancy look and maximum convenience at the same time, think no more and immediately find a perfect spot to mount your smart TV. Do not be concerned about how it is done because we are here to assist you to the fullest. Follow our step by step guide to get your flat screen TV safely on the wall. Make sure you have all the tools required. In case, you don’t have any of the tools available, simply find an alternative for it.
- Checklist of Tools Needed
There are certain tools you must gather before you start mounting your TV on the wall. You will be needing them throughout the process. These include:
If you want to avoid any mess, we suggest you not to mount your TV on any drywall. It is always wise to mount it with the help of a stud for a lasting attachment. A stud finder proves very helpful to fulfill this purpose. It is necessary to maximize the support with studs otherwise your TV might end up crashing into pieces.
A screwdriver can be used to mount the TV but it might take longer. To avoid any strenuous effort it is suggested to use a power drill for this purpose.
Masonry Bits with Carbide Tips
These are used to make holes in the wall where the mounting screws are supposed to be drilled.
Smart TV Mount
In order to fix your TV on the wall, a TV mount is needed according to your TV model. You can check out further details regarding the measurements by using your TV manual. This will help you in finding the right TV mount. You can further check out some good mounts here.
Once the wall studs have been located, you can mark them using painter’s tape. Painter tape is more convenient as they are more visible as compared to a pencil. After all, you will not want to damage your wall by leaving unnecessary pencil marks.
No matter how sharp your eyesight is, you better not rely completely on them when placing your flat-screen smart TV on the wall. It is advised to use a level to make sure you do not damage your TV. This will also prevent you from ruining your wall by making unwanted holes.
Cable management counts a lot as well when it comes to aesthetics. You do not want to ruin the look with the cables hanging. If you want a perfect finished look then you must look out for cable management options to get rid of any unwanted cable mess. It is always good to tie them up or hide them behind so they do not spoil the look. If it gets out of control, you can buy a matching cover that will help you hide the cables as well as enhance the overall look.
- Begin with Finding the Right Spot
To begin with, it is important to deeply observe all the walls in your house and pick out the best spot where you wish to mount your TV. It is indeed a critical decision to make in this whole process. Be careful with the angles because they play a pivotal role in determining the picture quality. Therefore, take your time and decide carefully.
You can move your TV to a different spot later if you want. But that might ruin your wall since you are going to end up leaving unnecessary holes behind. Different people might have varying favorite spots to enjoy watching TV. For some, this ideal location to mount a TV can be above the fireplace or in their lounge area. The focal points may vary.
- Look out for Wall Studs
After you have finally decided on your ideal spot, it is time to use a stud finder to look out for the wall studs. You can move the stud finder all across the wall and look out for any studs. When you are done with finding the right spot, make sure that you mark it properly.
- Its Drilling Time
Now drill small holes at the marks to mount the screws in the wall. You might need help so you can ask someone to help you around.
Now you can hold the mount leveled straight up to the wall. You can use chalk to mark the points where you want to drill the holes. You can make use of a masonry bit while drilling the holes.
Now it is time to fix the mounting bracket upon your wall. For that, you will have to position the mount against the wall and start drilling the screws into the small holes you created earlier.
- Fixing the Mounting Plate
You can now fix the mounting plate on your TV. Make sure you have already removed the stand of your TV.
- Spot The Attachment Holes
The next step is to spot the attachment holes of the mounting plate located at the backside of your TV. They often come with plastic covers. Chances are that there might already be screws inside. Check if they are present and remove them. Now fix the plate at the backside of the TV along with the other hardware.
- The Final Stage
Attach your flat screen smart TV to that chosen spot on the wall. Voila! You have successfully completed the process! It is always a good idea to get someone’s help while you are lifting and placing the TV on the wall in this final step. We do not want you to hurt yourself since you are likely to get a cramp if you are performing this step on your own.
Check if the mounting plate on the TV is aligned along with the bracket placed on the wall. Now make sure you have connected both of them with the help of the manual instructions provided by the manufacturer.
Now all that is left to do is connect your smart TV to a high-speed internet connection like AT&T internet and then grab onto your remote, sit back, relax, and enter the world of unlimited entertainment.